Airlive N.Power User Manual Page 65
- Page / 103
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
6. AP Mode
AirLive N.Power User’s Manual
60
Beacon Interval: The device broadcasts beacon frames regularly to announce its
existence. The beacon Interval specifies how often beacon frames are transmitted in
time unit of milliseconds. The default value is 100, and a valid value should be between
1 and 65,535.
Fragmentation: When the size of a unicast frame exceeds the fragmentation
threshold, it will be fragmented before the transmission. It should have a value of
256-2346 bytes, with a default of 2346. If you experience a high packet error rate,
you should slightly decrease the Fragmentation Threshold.
RTS Threshold: RTS/CTS frames are used to gain control of the medium for
transmission. Any unicast (data or control) frames larger than specified RTS threshold
must be transmitted following the RTS/CTS handshake exchange mechanism. The
RTS threshold should have a value between 256-2347 bytes, with a default of 2347. It
is recommended that this value does not deviate from the default too much.
Short Preamble: A preamble is a signal used in wireless environment to synchronize
the transmitting timing including Synchronization and Start frame delimiter. In a "noisy"
network environment, the Preamble Type should be set to Long Preamble. The Short
Preamble is intended for applications where minimum overhead and maximum
performance is desired. If in a "noisy" network environment, the performance will be
decreased.
Tx Burst and Packet Aggregate: These are the scheme used for improving the
performance of the data transmission in 11n and Turbo modes. It is recommended to
keep the settings on.
AckTimeOut: When a packet is sent out from one wireless station to the other, it will
wait for an Acknowledgement frame from the remote station. The station will only
wait for a certain amount of time; this time is called the ACK timeout. In most
conditions, please do not change the Tx and Rx Acktimeout value. The
N.Power’s default value is correct in most cases.
6.2.7 WMM Settings
Wireless Settings -> WMM Settings
Wi-Fi Multimedia (WMM) is a standard to prioritize traffic for multimedia applications. The
WMM Settings is to specify parameters on multiple data queue for better performance of
differentiated wireless traffic like Voice-over-IP (VoIP), other types of audio, video, and
streaming media as well as traditional IP data over the AP.
- N.Power 1
- Copyright & Disclaimer 2
- Table of Contents 3
- Introduction 6
- 1.3 Features 7
- 1.4 Operation Modes 7
- 1.4.1 Router Mode 8
- 1.4.2 AP mode 8
- 1.4.3 Client Mode 9
- 1.4.4 WDS Bridge Mode 9
- 1.4.5 WDS Repeater Mode 10
- Installing the N.Power 11
- 2.3 Knowing your N.Power 12
- 2.4 Hardware Installation 13
- 2. Installing the N.Power 14
- 2. Installing the N.Power 15
- 2.5 LED Table 17
- Configuring the 18
- 3.3.2 Web Menu Structure 20
- 3.4 Configuration Wizard 21
- 3.5 Change Operation Mode 22
- 3.6.1 AP and Router Modes 23
- PIN Code 24
- 3.6.2 Client Mode 25
- Configuration: Router 27
- 4.2.1 Setup Wizard 28
- 4.2.2 WAN Setting 29
- 4.2.3 Virtual Server 30
- 4.2.4 DMZ 31
- 4.2.5 URL Filtering 32
- 4.2.6 MAC Filtering 32
- 4.2.7 IP Filtering 33
- 4.2.8 DDNS 33
- 4.3 FTP Function 34
- 4.4 Wireless Settings Menu 37
- 4.4.2 Multiple SSID 38
- 4.4.3 Channel 38
- 4.4.4 Wireless Security 39
- 4.4.5 Access Control 40
- 4.4.6 Bandwidth Control 41
- 4.4.7 Associated Client 42
- 4.4.8 Advanced Settings 42
- 4.4.9 WMM Settings 44
- 4.4.11 WPS Settings 48
- System Configuration 51
- 5.2 LAN Interface Setup 52
- 5.3 Time Settings 53
- 5.4 Password Settings 54
- 5.6 Firmware Upgrade 55
- 5.8 Factory Default 56
- 5.9 Status Menu 56
- 5.9.2 Statistic 57
- 5.9.3 Client Table 58
- 5.9.4 LOG 58
- AP Mode 59
- 6.2 Wireless Settings 60
- 6.2.2 Channel 61
- 6.2.3 Wireless Security 62
- 6.2.4 Access Control 62
- 6.2.5 Associated Client 63
- 6.2.6 Advanced Settings 64
- 6.2.7 WMM Settings 65
- 6. AP Mode 66
- 6.2.9 WPS Settings 69
- Client Mode 72
- 7.2.1 Profile Setting 73
- 7.2.2 Site Survey 74
- 7.2.3 Advance Settings 75
- 7.2.4 WPS Settings 76
- 7. Client Mode 78
- WDS Bridge Mode 79
- 8.2.1 Advance Setup 80
- 8.2.2 WDS Settings 81
- 8. WDS Bridge Mode 82
- Emergency Firmware 83
- Recovery 83
- Frequent Asked 85
- Questions 85
- Specifications 87
- 11.2 Radio Specifications 88
- 11.3 Software Features 89
- Wireless Network 90
- Glossary 90
Related products and manuals for Routers Airlive N.Power
Routers Airlive N450R User Manual
(108 pages)
(108 pages)
Routers Airlive Traveler3G User Manual
(124 pages)
(124 pages)
Routers Airlive VoIP-400 Series User Manual
(56 pages)
(56 pages)
Routers Airlive WL-1500R User Manual
(60 pages)
(60 pages)
Routers Airlive WL-1600GL User Manual
(115 pages)
(115 pages)
Routers Airlive WL-5470AP User Manual
(50 pages)
(50 pages)
Routers Airlive WMM-3000R User Manual
(97 pages)
(97 pages)
Routers Airlive WN-200USB User Manual
(56 pages)
(56 pages)
Routers Airlive WN-220ARM User Manual
(72 pages)
(72 pages)
Routers Airlive WN-250R User Manual
(160 pages)
(160 pages)
Routers Airlive WN-250USB User Manual
(60 pages)
(60 pages)
Routers Airlive WN-300R User Manual
(110 pages)
(110 pages)
Routers Airlive WN-301R User Manual
(110 pages)
(110 pages)
Routers Airlive WN-350R User Manual
(176 pages)
(176 pages)
Routers Airlive WT-2000ARM User Manual
(65 pages)
(65 pages)
Magnetic-products Samarium Cobalt Deep Pot Magnets podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Sprzęt komputerowy Magnetic-products Samarium Cobalt Deep Pot Magnets.
Dostarczamy 1 pdf podręczników Magnetic-products Samarium Cobalt Deep Pot Magnets do pobrania za darmo według typów dokumentów: Instrukcja Użytkownika
Comments to this Manuals