AirLive IGR-1500 User Manual

IGR-1500 Four-WAN Internet Gateway User’s Manual

7CCChhhaaapppttteeerrr 222 DDDeeepppllloooyyymmmeeennnttt IGR-1500 provides one LAN port connecting to your network devices such as PC, HU

8CCChhhaaapppttteeerrr 333 CCCooonnnfffiiiggguuurrreee RRRooouuuttteeerrr 3.1 How to start out to configure router Step1. Connect the M

Figure 3-2 Select Work Mode Each working mode includes different features: Function Mode LAN to WAN Throughput NAT FunctionDMZ, DoS, Virtual Serve

Step4. Configure each WAN port separately, and the other function you would like to use, such as Load Balance, Bandwidth Management, or else. (Figure

113.2 Work Mode In order to meet different application usage, you can configure this router into 3 different working modes.  Gateway mode  Router

12Time Zone V V V System Log V V V Mac Address Clone V V V Configure Proxy V V Routing protocol V V V DOD (PPPoE) V V Bandwidth Usag

3.3 System Status 3.3.1 Link Status You can get the following information in Link Status window: (Figure 3-4) - LAN Status - WAN Status - Firmwa

3.3.2 Data Monitor Differ with Link Status window, Data Monitor window provides detail packet transfer status. It includes 2 kinds of real time data

 NAT Table: list current user detail NAT data. (Figure 3-6)  Refresh: update data monitor table to display newest data  Clear Counter: reset Dat

3.4 WAN Configure There are several WAN function can be made in this display, you can configure functions to each WAN port separately.  Connect to

Declaration of ConformityWe, Manufacturer/ImporterDeclare that the productFour-WAN Internet GatewayIGR-1500is in conformity withIn accordance with 89/

 WAN Link Mode: You can choose the WAN interface type in order to follow the connecting type of ISP.  Auto Sense  10Mbps Half Duplex  10Mbps F

3.4.2 WAN Type – PPPoE Connect to ISP via dial-up connecting, ISP will assign a legal IP to you after the user Id and password had been passed. (The

About “Always-on” function, normally you need to combine "Healthy Check" function together, then "Always-on" can work more perfe

3.5 Bandwidth Usage This is a very useful function, it can let you to control WAN port bandwidth usage by each protocol. Like FTP, when someone uses

The totally amount of protocol usage percentage can not exceed 100% for each WAN port. Router provides another 4 self-defined port number, user ju

3.6 Configure LAN & DHCP This function configures the LAN ports IP address, Subnet Mask, and DHCP server. You can choose using DHCP server or di

Figure 3-13 Add Reserved IP Address When enable DHCP Server in “From”, ”TO” field, you can reserve up to 253 IP address to DHCP server. Fill in

3.7 Routing Table 3.7.1 Configure This function allows manually defined by users as the only path to the destination. Users can configure the static

 Static Routing – Basic NAT Mode Similar to Gateway mode, the difference is that Basic NAT mode only has Basic NAT function. Once you select Basic N

3.7.2 Current Table This display shows the valid routing paths in IGR-1500. Users can view the information about current routing paths. (Figure 3-16)

AirLive IGR-1500 CE Declaration StatementCountry Declaration Country DeclarationcsČesky [Czech]OvisLink Corp. tímto prohlašuje, že tento AirLive IGR-1

273.8 Access Control 3.8.1 Local IP Filtering (Gateway Mode only) AirLive IGR-1500 allows you to define the accessed restriction about to block or

Figure 3-17 Local IP Filtering Example Setting  Protocol Port Number List Protocol Service Port no. Protocol Service Port no. TCP FTP 21 TCP L

3.8.2 Remote IP Filtering (Gateway Mode only) AirLive IGR-1500 features to define accessed restriction for remote users. You may restrict some destin

3.8.3 Intrusion Security (Gateway Mode only) AirLive IGR-1500 features Intrusion Security, to allow user setting as “BLOCK” or “PASS” function follow

3.8.4 DoS Defense (Gateway Mode only) AirLive IGR-1500 also provides DoS (Denial of Service Defense) function to protect your network servers, hosts,

Some virus are using “PING” command to attack network, AirLive IGR-1500 can be defined as accept or reject “PING” command from WAN or LAN. (Figure 3-2

3.8.5 URL Filtering (Gateway Mode only) Besides restrict users by local/destination IP, AirLive IGR-1500 provides you to do accessed restriction for

3.9 QoS With QoS function, you can set up user bandwidth with Maximum & Minimum bandwidth value.  Configure WAN Speed: The WAN speeds must be

3.10 Load Balance 3.10.1 Outbound Load Balance AirLive IGR-1500 provides three kinds of work mode for Outbound Load Balance, and Ultra Smart Sharing

Figure 3-26 Outbound Load Balance – Weight round robin  Dynamic Traffic: Router will find the lowest loading WAN port to transmit and receive data

1Copyright The contents of this publication may not be reproduced in any part or as a whole, stored, transcribed in an information retrieval system,

 Ultra Smart Sharing: When user enables this function, IGR-1500 will lock user packet at dedicated WAN port, the dedicated WAN port will be selected

3.10.3 Special Application Some Internet WEB server do not allow access with multi WAN address, also these WEB server was using dynamic IP address, i

3.10.5 TOS TOS function can let you setting the priority for dedicated packet. (Figure 3-32) User can specify the Source IP, Destination IP, Protocol

3.11 Advance 3.11.1 Remote Configure The AirLive IGR-1500 can be managed from any PC from Internet. If enable “Remote Configure” function, remote us

3.11.2 Virtual Server AirLive IGR-1500 ALG Options to allow IPSec, PPTP and VoIP pass-through, user can also define the port number for ALG Options.

Figure 3-36 Virtual Server For example: (Figure 3-37) Suppose you want to install servers dedicated with specific WAN port as following: 1. Internet

Figure 3-37 Example Topology Example 1: Define Virtual server to allow FTP service (TCP 21) packets from Internet to LAN FTP server via WAN1. (Figu

Example 2: Define Virtual server to allow VNC service (TCP 5800, TCP 5900) packets from Internet to LAN VNC client via WAN2. (Figure 3-39) Figure 3-

3.11.3 DMZ Host The Demilitarized Zone (DMZ) function provides a way for public servers (Web, e-mail, FTP, etc.) to be visible to the outside world (

 Dynamic IP DMZ: When a WAN port IP is assigned by ISP and obtained by PPPoE or Dynamic IP, you can use this section to specify the DMZ host disrega

2Table of Contents Chapter 1 Introduction...

3.11.4 Multi-NAT Multi-NAT function allows you to configure multiple LAN IP domain to each WAN port (total 10 LAN IP can be defined), after configure

483.11.5 IP Binding In Internet world, there have some Game Server, SSL protocol user or Personal Server have special request for connection, these s

Example: IP Address Start port End Port WAN210.3.1.23 0 65535 WAN1 All packets go to Internet Host wi

3.11.6 DDNS (Gateway mode and Basic NAT mode only) You need to apply for a free DNS domain name from www.dyndns.org or the other DDNS service provide

3.11.7 Proxy (Gateway mode and Basic NAT mode only) This function works together with Mail Alert function, if there have Proxy Server in your local L

3.11.8 Mail Alert (Gateway mode and Basic NAT mode only) Enter the Receiver/ Sender e-mail Address in the fields and check the items you want. System

3.11.9 Time (Gateway mode and Basic NAT mode only) AirLive IGR-1500 will obtain the GMT (Greenwich Mean Time) after connected to Internet. You need t

3.11.10 System Log (Gateway mode and Basic NAT mode only) Show all the records after IGR-1500 Power on, such as WAN port up/down, WAN IP address, the

3.11.11 MAC Address Clone If your ISP blocked the MAC address of a network card, you may use MAC Address Clone to duplicate the MAC address to the Ma

3.12 Administrator 3.12.1 Password Use this function to change the Password that is used for access the web configuration. Type in the Old Password,

33.11.5 IP Binding ... 48 3.

3.12.2 Backup & Restore Use Backup & Restore function to save all the settings parameters to PC for safety issue, in order to avoid all param

3.12.3 Load Factory Default User can use this function to define the feature of reset button, or load the latest configuration file back to device. C

3.12.4 Display You can use this function to check all the parameter setting in this router, in order to save time to check every display. (Figure 3-5

3.13 Firmware Upgrade AirLive IGR-1500 allows you to easily update the embedded firmware. We will occasionally provide new firmware on the web site t

Step 3: Click Update to update the firmware. Method 2: Step 1: Run a TFTP server program such as TFTPD32. (TFTPD32 is a shareware and you may do

Step2: Make a base directory in this server Step 3: Save the image file of firmware to the directory of TFTPD32 62

Step 4: Enter the Server Name and File Name in the new folder fields of Firmware Update window and then click Ok. Step 5: You will see the updating

3.14 Save & Reset In order to save the configuration changes that have been made to the IGR-1500, you must save them to the IGR-1500’s Flash memo

65AAAppppppeeennndddiiixxx AAA IIInnn---BBBooouuunnnddd LLLoooaaadddB BBaaalllaaannnccceee FFFuuunnnccctttiiiooonnn Authorities DNS i

A.1 Simple Load Balance (2 WAN lines; Session 1:1) Let us assume that the upload speed of WAN1 and WAN2 are the same; so we will use inbound load-bal

4 CCChhhaaapppttteeerrr 111 IIInnntttrrroooddduuuccctttiiiooonnn Congratulations on your purchase of this outstanding IGR-1500 Four-WAN Int

Step 2: Enter host1.example.com two times, once for WAN1 and once for WAN2 with Address Type. This display show the 1st time for WAN1, after clic

Step 4: This time we are adding the DNS record with the real name for web server. Select DNS Type with Canonical Name. Name: www.example.com

Now the Inbound Load-balancing DNS Server is configured to redirect the Internet requests of www.example.com to the IP address of either WAN1 or WAN2.

A.2 Advanced Load Balancing We will describe Inbound Load Balancing using “Weighted round robin” algorithm for three Internet servers: 1. Web serve

 Define www.example.com in Inbound Option In Load Balance Æ Inbound, select Weight round robin for the inbound load balance mode. Now you can ent

The mail server requires some additional steps.  Define mail.example.com in Inbound Option Step 1: In Load Balance Æ Inbound page, click Add new i

Step 3: Load Balance Æ Inbound Æ Add new item Æ Configure Inbound (CName): Select Canonical Name and enter the name as smtp.example.com, select Host

Step 6: Load Balance Æ Inbound: The Mail Server is configured by the last 5 entries of the DNS Name table. Step 7: Advance Æ Virtual Server:

The ratio was specified: WAN1, WAN2, WAN3, WAN4 = 1:2:3:4  www.example.com uses WAN1 and WAN2 with a ratio of 1:2. The IP addresses return to t

1.2 Front Panel and Rear Panel Figure 1-1 Front Panel LED Status Indicator Color ON Flashing Power ● Green Power on - ● Green Linked Data T

61.3 Packing List z IGR-1500 Four-WAN Internet Gateway z Installation CD-ROM z Quick Installation Guide z CAT-5 UTP Fast Ethernet cable z AC Adap