Airlive VoIP-120A User Manual

AirLive VoIP-111A / 120A User’s Manual 0 VoIP-111A / 120A SIP VoIP ATA Adapter User’s Manual

3.1.3 If you change the setting in the Web Management interface, please remember to click the “Submit” button in that page. After you finished the

-4- Figure 2. Speed Dial 3.4 Phone Setting 3.4.1 In Phone Setting there are Call Forward, SNTP Settings, Volume Settings, Block Setting, Calle

Figure 3. Forward Setting 3.4.3 SNTP Setting function: you can setup the primary and second SNTP Server IP Address to get the date/time informati

3.4.4 Volume Setting function: you can setup the Handset Volume, Ringer Volume, and the Handset Gain. When you have finished the setting, please c

Figure 6. DND Setting 3.4.6 Caller ID function: displays Caller ID in your PSTN Phone or IP Phone. -1- There are four selection of Caller

3.4.7 Auto Dial Setting function: This function is when you input the phone number by the keypad but you don’t need to press “#”. After time o

For example: Figure 9. Virtual Server Setting 1：Drop prefix: No, Replace rule 1: 002, 8613+866

Comment 4：if you dial out number not match setting rule ,device should dial out you dial number 。 5： Dial now: *xx+#xx+11x+xxxxxxxx Explanation 1: I

3.4.9 Call Waiting Setting function: You can Enable/Disable the Call Waiting function. When there is a new incoming call while you are talking

3.5 Hot line This function supports auto dial for you to set a hot line number. When you set this function the device should

Declaration of ConformityWe, Manufacturer/ImporterDeclare that the productSIP VOIP ATA AdapterVOIP-111A , VOIP-120Ais in conformity withIn accordance

3.7 Network 3.7.1 In Network you can check the Network status, WAN setting,LAN setting,DDNS settings and VLAN Settings. 3.7.2 Network Status: You

3.7.3 WAN and LAN Settings: -1- If you change the WAN port’s setting to Fix IP Mode, then you have to make sure the IP address. Net Mask, Gatewa

3.7.4 Bridge Setting: If you don’t want to use the NAT Mode, then you can set the network setting in this page. -1- The TCP/IP Configuration ite

3.7.5 DDNS Setting: You can configure the DDNS setting in this page. You need to have the DDNS account and input the information properly.

3.7.6 VLAN Setting: You can set the VLAN setting in this page. There are two parts in this page. First one is to set the packets related to the

3.8 DMZ Setting DMZ setting: you can set the DMZ setting in this page. Figure 18. DMZ Setting 3.9 Virtual Server Setting Figure 19.Virtual

Virtual Server Page To browse through different pages, click on the drop down box and select the page number you wish to view. Num This column disp

Figure 20. Service Domain Setting 3.10.4 Port Settings: you can setup the SIP and RTP port number in this page. Each ISP provider will have

3.10.5 Codec Settings: you can setup the Codec priority, RTP packet length, and VAD function in this page. You need to follow the ISP suggestion

3.10.7 DTMF Setting: you can setup the RFC2833 Out-Band DTMF, Inband DTMF and Send DTMF SIP Info in this page. To change this setting, please fol

VOIP-111/120A CE Declaration StatementCountry Declaration Country DeclarationcsČesky [Czech]OvisLink Corp. tímto prohlašuje, že tento VOIP-111/120A je

packets’ priority. If you set the value higher than 0, then the voice packets will get the higher priority to the Internet. But the QoS function

3.12 Others 3.12.1 In Others you can setup Auto Config, PTT Setting and ICMP Setting function. The function can configure your VoIP Phone automa

3.12.5 Auto configuration example Example 1: Auto Configuration: HTTP，HTTP Server: 192.168.1.50，HTTP Path: /file/。 Explanation： device will connec

Explanation 1：open the [MACList.txt] file then enter the these information in order[MAC Address, Display Name, User Name, Register Name, Register Pas

Figure 29. Advanced Setting ICMP Not Echo Default setting is No (do not activate). Once activated all ping messages will not be responded. Send A

3.12.9 FXS impedence Setting: you can setup the FXS in this page. When you are using different country’s PSTN Phone, you have to set the count

3.14 Tone Settings: you can configure your tone settings in this page . 3.15 System Authority 3.15.1 In System Authority you can change y

3.16 Save Change 3.16.1 In Save Change you can save the changes you have done. If you want to use new setting in the ATA, You have to click the

Figure 33. Update System and Settings. 3.17.3 In Default Setting you can restore the TA to factory default in this page. You can just cli

3.18 Reboot 3.18.1 If you want to restart the ATA, just click the Reboot button, then the ATA will reboot automatically. Figure 35. Reboot Syst

FCC Certifications This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rul

4. Setup the ATA by using Console (Hyper Terminal) 4.1 Configure the COM port First, open the hyper terminal window, select the connection by the

4.2 ATA Login After finishing the setting, click the “Connect” button (looks like a telephone icon). Then the hyper terminal is ready to connect

-1- “?” function is to show CLI command list in the screen. -2- arp function Index Command Description 1 ? Show 'arp' Option 2 -a Sho

3 -dsp Update DSP Image(IP filename) 4 -all Update All Image(IP filename) 5 -server Update Server (IP filename length) 6 -pcm PCM(IP file

-11- dns function Index Command Description 1 ? Show 'dns' Option 2 -q DNS query. dns -q domain-name 3 (null) Show DNS Table -12-

6 -mode Set SNTP Client Mode 7 -zone Set GMT Time Zone: [+|-][hour]:[min] 8 -adjust Set Adjustment Time: [second] 9 (null) Show SNTP Setting -1

-24- weblogo function Index Command Description 1 ? Show 'weblogo' Option 2 -on Vender Logo 3 -off Default Logo 4 (null) Show weblog

5. How to make a phone call When your ATA is configured properly, you can make a phone call to your friend in the same Service provider. If you want

Table of Contents 1. Introduction... 2 1.1 Hardware Overview...

1. Introduction This user’s manual is for VoIP-111A (1PSTN+1Phone) / VoIP-120A (2Phone) VoIP terminal adapter (ATA). This user’s manual will expla

2. Keypad Interface for The ATA You can use the PSTN phone keypad to operate the ATA. Please follow the instruction to configure your terminal adap

Setting Set DHCP client #111# None The system will change to DHCP Client type Setting Set Static IP Address #112xxx*xxx*xxx*xxx#Enter IP address

3. Setup the ATA by Web Browser (LAN Connection) The ATA provides a built-in web server. You can use a Web browser to configure the ATA. For m